⟵ Return to U-Anchor 2000 Single Ply

Installation for U-Anchor 2000 Single Ply

On this page you'll find instructions for installation of the U-Anchor 2000. There are two different methods for each type with and without the membrane attachment ring. Please scroll down to read more about each method.


 

PVC, TPO or KEE

  1. Prepare the roof surface by removing all loose debris and clean the area in accordance with the roofing manufacture recommendations
  2. Place the U-Anchor 2000 over the roof membrane and alien as per engineering requirements using the notched alignment marks on each side of the cover.   
  3. Hot air weld the entire perimeter edge of the U-Anchor membrane cover to the roof surface below. (Weld should be consistent with the roofing manufactures recommendations or a minimum 1.5 inches whichever is greater)

 

 

 

PVC, TPO or KEE with Membrane Attachment Ring

  1. Prepare the roof surface by removing all loose debris and clean the area in accordance with the roofing manufacture recommendations
  2. Align the Membrane Attachment Ring as per engineering requirements and fasten using 3 to 7 fasteners as specified.  
  3. Place and center the U-Anchor 2000 over the Membrane Attachment Ring and using the notched alignment marks on each side of the cover.
  4. Hot air weld the U-Anchor Target around the inside diameter of the Membrane Attachment Ring (Weld should be consistent with the roofing manufactures recommendations or a minimum 1.5 inches whichever is greater)   
  5. Hot air weld the entire perimeter edge of the U-Anchor membrane cover to the roof surface below. (Weld should be consistent with the roofing manufactures recommendations or a minimum 1.5 inches whichever is greater)

 

 

 

EPDM

  1. Prepare the roof surface by removing all loose debris and clean the area in accordance with the roofing manufacture recommendations   
  2. Apply an approved Seam Slice Adhesive Primer to the roof membrane where the Double Sided Die Cut Adhesive will be placed and allow to dry before continuing.  
  3. Peel back half of the release liner exposing the adhesive.
  4. Carefully align the Double Side Die Cut Adhesive and place into the desired position.  Do not stretch or pull the adhesive. 
  5. Apply an approved Seam Slice Adhesive Primer to the underside of the U-Anchor 2400 Single Ply cover and allow to dry before continuing.  
  6. Remove the top release liner and place into position. 
  7. Center and place the U-Anchor 2000 over the Double Sided Die Cut Adhesive avoiding wrinkles.
  8. Using a weighted membrane roller firmly roll the entire surface of the U-Anchor membrane cover to ensure a proper bond is achieved.  
  9. Firmly roll the perimeter edge to embed the perimeter edge of the membrane in the adhesive.  If you are unable to embed the edge of the membrane into the adhesive cut edge sealant may be needed to prevent the membrane reinforcement from wicking moisture.

 

 

 

EPDM with Membrane Attachment Ring

  1. Prepare the roof surface by removing all loose debris and clean the area in accordance with the roofing manufacture recommendations   
  2. Apply an approved Seam Slice Adhesive Primer to the roof membrane where the Double Sided Die Cut Adhesive will be placed and allow to dry before continuing.  
  3. Peel back half of the release liner exposing the adhesive.
  4. Carefully align the Double Side Die Cut Adhesive and place into the desired position.  
  5. Using a weighted roller firmly roll over the entire surface of the Die Cut Adhesive insuring a proper bond achieved.
  6. Center the Membrane Attachment Ring over the Double Sided Adhesive and fasten using 3 to 7 fasteners as specified.
  7. Apply an approved Seam Slice Adhesive Primer to the underside of the U-Anchor 2400 Single Ply cover and allow to dry before continuing.  
  8. Remove the release liner exposing the top surface of the adhesive.
  9. Center and place the U-Anchor 2000 over the Double Sided Die Cut Adhesive and Membrane Attachment Ring.
  10. Using a weighted membrane roller firmly roll the entire surface of the U-Anchor membrane cover to ensure a proper bond is achieved.  
  11. Firmly roll the perimeter edge to embed the perimeter edge of the membrane in the adhesive.  If you are unable to embed the edge of the membrane into the adhesive cut edge sealant may be needed to prevent the membrane reinforcement from wicking moisture.